Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
- 10. Brake system
   10.1. Introduction
   10.2. Technical characteristics
   10.3. Replacement brake колодок on disk brakes
   10.4. A support of disk brakes
   10.5. A brake disk
   10.6. Replacement brake колодок drum-type brakes
   10.7. The working brake cylinder
   10.8. The main brake cylinder
   10.9. Brake pipelines and hoses
   10.10. Replacement of a regulator of pressure
   10.11. Prorolling of hydraulic brake system
   10.12. Adjustment of a manual brake
   10.13. Replacement of a cable of a manual brake
   10.14. Replacement brake колодок a manual brake on back disk brakes
   10.15. Additional brake system
   10.16. The vacuum amplifier of brakes
   10.17. The stoplight switch
   10.18. Antiblocking system of brakes (ABS)
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





10.14. Replacement brake колодок a manual brake on back disk brakes
THE GENERAL DATA

Details of a manual brake on back disk brakes

1 – a brake board
2 – скоба
3 – a spring washer
4 – the lever of a manual brake
5 – a lobby колодка a manual brake
6 – back колодка a manual brake
7 – a spring
8 – a directing lath
9 – a fastening plate
10 – a returnable spring of a lobby brake колодки
11 – a returnable spring back brake колодки
12 – a regulator
14 – a spring plate
15 – a spring
16 – a pin
17 stopper

On models with back brake disks the manual brake works irrespective of hydraulic brake system. Are thus used brake колодки drum-type type, and as a brake drum the internal part of a brake disk is used.
The prevention

Necessarily make replacement of all колодок even if deterioration borders has reached one колодка.

At work brake колодок the brake dust which contains asbestos, unhealthy is formed. Therefore at clearing brake колодок do not use compressed air and do not inhale a dust.


PERFORMANCE ORDER
1. Remove a brake disk.
2. If the brake disk does not act in film from a nave, check up that the lay brake is completely released.
3. If the brake drum still does not act in film from a nave, it is necessary to take away from it brake колодки. It can be executed after removal of a stopper from a brake board.
4. Using a screw-driver or the bent lever, rotate a gear adjusting wheel and take away brake колодки from a brake disk.
5. Using a special liquid, clear brake колодки a manual brake.
6. Check up a condition of a brake disk. Measure a thickness of a brake disk and diameter of a brake drum. The minimum thickness of a brake disk (at the left) and the maximum diameter of a brake drum (on the right) are beaten out on an internal surface of a brake disk.
7. Remove a plate of a spring of fixing of a lobby brake колодки, pressing a plate and turning it on 90 .
8. Remove a plate of a spring of fixing back brake колодки, pressing a plate and turning it on 90 .
9. Remove the top returnable spring back brake колодки.
10. Remove directing lath and a spring.
11. Remove the top returnable spring of a lobby brake колодки.
12. Remove brake колодки together with a regulator and the bottom returnable spring.
13. Put a layer of high-temperature greasing on a brake board in places of contact of a board with brake колодками.
14. Establish the lever of a manual brake on new back brake колодку, connect to the lever a cable of a manual brake and establish back brake колодку.
15. Establish a spring and a clamp back brake колодки, pressing a clamp and turning it on 90 .
16. Establish directing lath together with a spring on back brake колодку.
17. Establish the bottom returnable spring and a regulator on brake колодки.
18. Establish a lobby brake колодку into place, having combined it with directing brake колодок.
19. Establish a spring and a clamp of a lobby brake колодки, pressing a clamp and turning it on 90 .
20. Establish the top returnable springs forward and back brake колодок.
21. Repeat operations on replacement колодок a manual brake on the second wheel.
22. Establish a brake disk. Rotating a screw-driver a regulator wheel, dissolve brake колодки so that the brake disk rotated without appreciable resistance.
23. Establish holders of a support, brake колодки and a support.
24. Establish wheels and lower the car.