Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
- 10. Brake system
   10.1. Introduction
   10.2. Technical characteristics
   10.3. Replacement brake колодок on disk brakes
   10.4. A support of disk brakes
   10.5. A brake disk
   10.6. Replacement brake колодок drum-type brakes
   10.7. The working brake cylinder
   10.8. The main brake cylinder
   10.9. Brake pipelines and hoses
   10.10. Replacement of a regulator of pressure
   10.11. Prorolling of hydraulic brake system
   10.12. Adjustment of a manual brake
   10.13. Replacement of a cable of a manual brake
   10.14. Replacement brake колодок a manual brake on back disk brakes
   10.15. Additional brake system
   10.16. The vacuum amplifier of brakes
   10.17. The stoplight switch
   10.18. Antiblocking system of brakes (ABS)
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





10.3. Replacement brake колодок on disk brakes
THE GENERAL DATA

Forward brake knot

1 – the holder of a support
2 – internal brake колодка
3 – external brake колодка
4 – a directing finger
5 – a protective cover
6 – a protective cover
7 – the plug
8 – a directing finger
9 – an antitinkling sound spring
10 – an external lining brake
колодки
11 – a lining
12 – a lining
13 – a forward brake disk
14 – a mudguard
15 – a bolt
16 – a washer
17 – the prorolling union
18 – the piston
19 – a sealing ring of the piston
20 – a dustproof cover
21 – a support

Support of a back brake

1 – linings
2 – internal brake колодка
3 – the holder of a support
4 – external brake колодка
5 – a directing finger
6 – a bolt of a directing finger
7 – a protective cover

8 – the plug of a directing finger
9 – a support
10 – the piston
11 – a dustproof cover
12 – the prorolling union
13 – an antitinkling sound spring

The prevention

Necessarily make replacement of all колодок on one axis of the car, even if deterioration borders has reached one колодка. If колодки will be repeatedly established, before removal they are necessary for marking.

At work brake колодок the brake dust which contains asbestos, unhealthy is formed. Therefore at clearing brake колодок do not use compressed air and do not inhale a dust.


PERFORMANCE ORDER
1. Lift the corresponding party of the car and fix on supports. Remove a wheel. If replacement brake колодок on back brakes is made, release a manual brake.
2. Pump out from пополнительного a tank of the main brake cylinder of two third of brake liquid. It is necessary that at piston cave-in in the brake cylinder the brake liquid did not pour out from пополнительного a tank.
3. Before the beginning of works clear brake knot with use of a special liquid.
4. Using a G-shaped clip, press the piston into the support cylinder.
5. Unscrew the bottom directing finger and turn a support upwards round the top directing finger.
6. Remove external brake колодку together with a lining.
7. Remove internal brake колодку together with linings.
8. Remove the bottom spring of an antitinkling sound.
9. Remove the top spring of an antitinkling sound.
10. Check up a condition of directing fingers and in the presence of defects replace them.
11. Check up a condition of dustproof covers of directing fingers.
12. Put a layer of high-temperature greasing on directing fingers.
13. On a basic surface new brake колодок put the structure interfering vibration brake колодок.
14. Establish an internal lining on brake колодку.
15. Establish an external lining on brake колодку.
16. Establish a lining on external brake колодку and put on linings a layer of the means interfering vibration brake колодок.
17. Establish the bottom spring of an antitinkling sound.
18. Establish the top spring of an antitinkling sound.
19. Establish external and internal brake колодки.
20. Establish a support and fix its bolts.
21. Replacement back brake колодок on disk brakes is made similarly.
22. Some times press a brake pedal that brake колодки have nestled on a brake disk. Check up level of a brake liquid in a tank.