Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
- 14. An electric equipment
   - 14.1. A body electric equipment
      14.1.1. Introduction
      14.1.2. Electric chains
      14.1.3. Detection of not closed chain
      14.1.4. Safety locks
      14.1.5. Chain breakers
      14.1.6. The relay
      14.1.7. The relay of turns and the emergency light alarm system
      14.1.8. Multipurpose switches of a steering column
      14.1.9. The ignition lock
      - 14.1.10. Replacement of switches of the panel of devices
         14.1.10.1. Models with 1990 for 1994
         14.1.10.2. Models since 1995
      14.1.11. A combination of devices
      14.1.12. A radio receiver
      14.1.13. Loudspeakers
      14.1.14. The aerial
      14.1.15. The aerial with the electric drive
      14.1.16. Replacement of bulbs of headlights
      14.1.17. Adjustment of light of headlights
      14.1.18. A headlight
      14.1.19. Replacement of bulbs накаливания
      14.1.20. The screen wiper engine
      14.1.21. A sound signal
      14.1.22. Check of a heater of back glass
      14.1.23. Стеклоподъемники with the electric drive
      14.1.24. Rear-view mirrors with the electric drive
      14.1.25. A safety air cushion
   + 14.2. Electroschemes





14.1.10. Replacement of switches of the panel of devices

14.1.10.1. Models with 1990 for 1994
THE GENERAL DATA

THE SWITCH OF ADJUSTMENT OF POSITION OF THE MIRROR

Arrangement of contacts on a socket of the switch of adjustment of position of a mirror and a condition of contacts on a socket at various positions of the switch


PERFORMANCE ORDER
1. Using an edge of a thin screw-driver, take the switch from a nest in the panel of devices.
2. Disconnect an electric socket from a switch underside.
3. Using an ohmmeter, check up a condition of contacts of the switch of adjustment of position of a mirror depending on switch position (the Arrangement of contacts fig. see a socket of the switch of adjustment of position of a mirror and a condition of contacts on a socket at various positions of the switch).
4. Connect to the switch an electric socket and insert the switch into a nest of the panel of devices before its accurate fixing.

THE SWITCH OF THE EMERGENCY LIGHT ALARM SYSTEM

Arrangement of contacts on a socket of the switch of the light alarm system and a condition of contacts on a socket at various positions of the switch

PERFORMANCE ORDER
1. Remove a decorative overlay of a combination of devices.
2. Unscrew screws and remove the switch from a decorative overlay of a combination of devices.
3. Using an ohmmeter, check up a condition of contacts of the switch of the light alarm system depending on switch position (the Arrangement of contacts fig. see a socket of the switch of the light alarm system and a condition of contacts on a socket at various positions of the switch).
4. Establish the switch on a decorative overlay of a combination of devices, fix screws, connect an electric socket, and establish a decorative overlay of a combination of devices.

THE SWITCH OF THE BACK ANTIFOG LANTERN

Arrangement of contacts of an electric socket and condition of contacts on a socket at various positions of the switch


PERFORMANCE ORDER
1. Using an edge of a thin screw-driver, take the switch from a nest in the panel of devices.
2. Disconnect from the switch an electric socket.
3. Using an ohmmeter, check up a condition of contacts of the switch of a back antifog lantern depending on switch position (the Arrangement of contacts of an electric socket and a condition of contacts fig. see a socket at various positions of the switch).
4. Connect to the switch an electric socket, and establish the switch in a nest of the panel of devices before accurate fixing of the switch.