Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
- 14. An electric equipment
   - 14.1. A body electric equipment
      14.1.1. Introduction
      14.1.2. Electric chains
      14.1.3. Detection of not closed chain
      14.1.4. Safety locks
      14.1.5. Chain breakers
      14.1.6. The relay
      14.1.7. The relay of turns and the emergency light alarm system
      14.1.8. Multipurpose switches of a steering column
      14.1.9. The ignition lock
      + 14.1.10. Replacement of switches of the panel of devices
      14.1.11. A combination of devices
      14.1.12. A radio receiver
      14.1.13. Loudspeakers
      14.1.14. The aerial
      14.1.15. The aerial with the electric drive
      14.1.16. Replacement of bulbs of headlights
      14.1.17. Adjustment of light of headlights
      14.1.18. A headlight
      14.1.19. Replacement of bulbs накаливания
      14.1.20. The screen wiper engine
      14.1.21. A sound signal
      14.1.22. Check of a heater of back glass
      14.1.23. Стеклоподъемники with the electric drive
      14.1.24. Rear-view mirrors with the electric drive
      14.1.25. A safety air cushion
   + 14.2. Electroschemes





14.1.19. Replacement of bulbs накаливания FORWARD TURNS AND DIMENSIONAL FIRES

PERFORMANCE ORDER
1. Open a cowl and unscrew the screw, which крепит a forward dimensional lantern to a wing.
2. Having pulled forward, take a forward dimensional lantern, turn the holder of a bulb counter-clockwise and take it from a lantern.
3. Turn a bulb counter-clockwise and take it from the holder.
4. Installation is made in sequence, return to removal.

BACK LANTERN

PERFORMANCE ORDER
1. Remove furnish of a luggage space opposite to a back lantern (arrows specify lamps накаливания in a back lantern).
2. Turn the holder of a bulb накаливания counter-clockwise and take it from a back lantern.
3. Press and in this position turn a bulb counter-clockwise and take it from the holder of a bulb.
4. Installation is made in sequence, return to removal.

THE STOPLIGHT AND BACKING LANTERN LOCATED IN THE COVER OF THE LUGGAGE CARRIER

PERFORMANCE ORDER
1. Remove furnish of a cover of a luggage carrier opposite to a lantern.
2. Turn the holder of a bulb накаливания counter-clockwise and take it from a back lantern.
3. Press and in this position turn a bulb counter-clockwise and take it from the holder of a bulb.
4. Installation is made in sequence, return to removal.

THE TOP STOPLIGHT

PERFORMANCE ORDER
Models with a body "sedan"
1. Disconnect an electric socket from the top stoplight.
2. Unscrew screws of fastening of the top stoplight.
3. Remove the top stoplight.
4. Installation is made in sequence, return to removal.
Models with a body "versatile person"
5. Remove decorative заглушки.
6. Unscrew the screws located under заглушками and uncover the top stoplight.
7. Having pulled upwards, take a lamp of the top stoplight from the holder.
8. Installation is made in sequence, return to removal.

LICENSE PLATE ILLUMINATION

PERFORMANCE ORDER
1. Unscrew screws, крепящие lanterns of illumination of licence plate.
2. Remove a plafond from a lantern of illumination of licence plate.
3. Having pulled on itself, take a bulb from a lantern of illumination of licence plate.
4. Installation is made in sequence, return to removal.

ILLUMINATION OF THE COMBINATION OF DEVICES

PERFORMANCE ORDER
1. Remove a combination of devices.
2. Turn the holder of a bulb counter-clockwise and take it from a payment of a combination of devices.
3. Having pulled for a bulb, take it from the holder.
4. Installation is made in sequence, return to removal.

SALON ILLUMINATION

PERFORMANCE ORDER
1. Using an edge of a thin screw-driver, remove a plafond of a lantern of illumination of salon.
2. Take a bulb of illumination of salon from contact clips.
3. Installation is made in sequence, return to removal.