Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
- 14. An electric equipment
   - 14.1. A body electric equipment
      14.1.1. Introduction
      14.1.2. Electric chains
      14.1.3. Detection of not closed chain
      14.1.4. Safety locks
      14.1.5. Chain breakers
      14.1.6. The relay
      14.1.7. The relay of turns and the emergency light alarm system
      14.1.8. Multipurpose switches of a steering column
      14.1.9. The ignition lock
      + 14.1.10. Replacement of switches of the panel of devices
      14.1.11. A combination of devices
      14.1.12. A radio receiver
      14.1.13. Loudspeakers
      14.1.14. The aerial
      14.1.15. The aerial with the electric drive
      14.1.16. Replacement of bulbs of headlights
      14.1.17. Adjustment of light of headlights
      14.1.18. A headlight
      14.1.19. Replacement of bulbs накаливания
      14.1.20. The screen wiper engine
      14.1.21. A sound signal
      14.1.22. Check of a heater of back glass
      14.1.23. Стеклоподъемники with the electric drive
      14.1.24. Rear-view mirrors with the electric drive
      14.1.25. A safety air cushion
   + 14.2. Electroschemes





14.1.20. The screen wiper engine
THE GENERAL DATA

If screen wiper brushes work with faults or is insufficiently effective, check up a safety lock condition in a chain of the engine of a screen wiper.

If the safety lock is serviceable, connect closing wire between the engine of a screen wiper and weight of the car and repeatedly check up work of the engine of a screen wiper.

If now the screen wiper engine works normally, restore connection of the engine with weight of the car.

If the engine still does not work, check up pressure giving to the screen wiper engine.

If pressure moves to the engine, and the engine does not work, remove the engine of a screen wiper and, using additional wires, connect it to the accumulator.

If the engine works now, check up a condition of an electric socket. If the engine still does not work, replace it.

THE ENGINE OF THE SCREEN WIPER OF THE WINDSCREEN

Arrangement of bolts of fastening of the engine of a screen wiper on models with 1990 for 1994


Arrangement of bolts of fastening of the engine of a screen wiper on models since 1995


PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. Remove levers of a screen wiper and an air inlet lattice. Disconnect from the screen wiper engine an electric socket.
3. Unscrew bolts of fastening of the engine of a screen wiper.
4. Put forward the engine of a screen wiper and disconnect draught from the engine. If the screen wiper engine is subject to replacement, unscrew a nut, крепящую draught of a screen wiper for an engine shaft.
5. If the engine is repeatedly established, disconnect other end of draught of a screen wiper from the screen wiper lever. Take the engine of a screen wiper from the car.
6. Unscrew 6 nuts.
7. The slevoj party take draughts of a screen wiper.
8. Installation is made in sequence, return to removal.

THE ENGINE OF THE SCREEN WIPER OF BACK GLASS

Arrangement of bolts of fastening of the back engine of a screen wiper on models with 1990 for 1994


Arrangement of bolts of fastening of the back engine of a screen wiper on models since 1995


PERFORMANCE ORDER
1. Unscrew a nut and remove the screen wiper lever.
2. Remove a protective head and unscrew a nut of fastening of a spindle of the engine.
3. Open a back door, remove an upholstery of a back door and remove a protective film from a door.
4. Disconnect an electric socket, unscrew bolts of fastening and take the engine of a screen wiper from a back door.
5. Installation is made in sequence, return to removal.