Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
- 2. Maintenance service
   2.1. Introduction
   2.2. Technical characteristics
   2.3. Periodicity of service
   2.4. Check of level of engine oil
   2.5. Level of a cooling liquid
   2.6. Level of a brake liquid and a liquid of a drive of coupling
   2.7. A liquid for a windscreen washer
   2.8. Accumulator check
   2.9. Tyres and pressure check in tyres
   2.10. Check of level of oil in an automatic transmission
   2.11. Check of level of a liquid in the steering amplifier
   2.12. Replacement of oil and the oil filter
   2.13. Check and accumulator service
   2.14. Accumulator gymnastics
   2.15. Check of system of cooling
   2.16. Check of hoses, tubes and their replacement
   2.17. Check and replacement of brushes of screen wipers
   2.18. Shift of tyres
   2.19. Suspension bracket and steering check
   2.20. Exhaust system check
   2.21. Check of level of oil in a transmission and the main transfer
   2.22. Check of level of oil in differential (the main transfer)
   2.23. Check of brake system
   2.24. Check of the vacuum amplifier of brakes
   2.25. Check of a manual brake
   2.26. Check of fuel system
   2.27. Replacement of the fuel filter
   2.28. Check and replacement приводного a belt
   2.29. Check of a free wheeling of a pedal of a brake
   2.30. Check of a free wheeling of a pedal of coupling
   2.31. Check and replacement of spark plugs
   2.32. Check of high-voltage wires
   2.33. Check and adjustment of turns of idling
   2.34. Replacement of the air filter
   2.35. Check and replacement of the valve of ventilation картера (PCV)
   2.36. Check of system of catching of steams of fuel
   2.37. Check of system of repeated burning of the fulfilled gases (EGR)
   2.38. Service of system of cooling
   2.39. Replacement of a brake liquid
   2.40. Oil replacement in an automatic transmission
   2.41. Oil replacement in a mechanical transmission
   2.42. Check and adjustment of backlashes of valves
   + 2.43. The basic malfunctions
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





2.12. Replacement of oil and the oil filter
THE GENERAL DATA

The tools necessary for replacement of oil and the oil filter

1 – the flat wide container for oil plum
2 – rubber gloves for an exception of hit of hot oil on hands
3 – the extended handle of a key
4 – a key for unscrewing маслосливной stoppers
5 – a special key for unscrewing of the oil filter
6 – a special key for unscrewing of the oil filter, established on a back part of the filter

Periodic replacements of oil and the filter – the most important preventive procedures of maintenance service. When engine oil grows old, it becomes liquid and polluted that conducts to premature deterioration of the engine.

Before the beginning of this operation gather all necessary tools and materials. It is necessary, that the engine was warm that oil flew down together with a great bulk of polluting substances is better.

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports.
2. Unscrew a drain stopper approximately on half of turn. Place the container for oil plum under a drain stopper and unscrew a stopper completely. If it is necessary, press a stopper when unscrew that oil did not proceed prematurely.
3. When oil completely will flow down, wipe all round a drain aperture a rag and reliably screw up маслосливную a stopper.
4. Establish the container for merged oil under the oil filter and, using the special tool, ослабьте the filter, then unscrew his hand.
5. Wipe all traces of oil and a dirt round a place of fastening of the filter. Check up, whether there was a rubber consolidation on the block of cylinders. If it remains, remove it.
6. Grease rubber consolidation of the new oil filter by pure engine oil.
7. Screw in a hand the oil filter to a contact of a rubber lining with the engine, then довинтите the filter a hand on 3/4 turns.
8. Establish the car on an equal horizontal surface.
9. Fill in fresh engine oil through маслоналивную a mouth.
10. Close a cover маслозаливной mouths, start the engine and allow to it to work some minutes. Check up it about leaks of oil round the filter and a drain stopper on the oil pallet. Keep in mind that the emergency bulb of pressure of oil can burn some seconds as oil should fill all channels and oil capacities in the engine.
11. Switch off the engine and wait some minutes that oil has flown down in the pallet. Check up level of oil and add, if it is necessary.

The prevention

If at the fulfilled engine oil there is a metal shaving, it usually specifies in deterioration radical or шатунных bearings of a cranked shaft.