Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
- 2. Maintenance service
   2.1. Introduction
   2.2. Technical characteristics
   2.3. Periodicity of service
   2.4. Check of level of engine oil
   2.5. Level of a cooling liquid
   2.6. Level of a brake liquid and a liquid of a drive of coupling
   2.7. A liquid for a windscreen washer
   2.8. Accumulator check
   2.9. Tyres and pressure check in tyres
   2.10. Check of level of oil in an automatic transmission
   2.11. Check of level of a liquid in the steering amplifier
   2.12. Replacement of oil and the oil filter
   2.13. Check and accumulator service
   2.14. Accumulator gymnastics
   2.15. Check of system of cooling
   2.16. Check of hoses, tubes and their replacement
   2.17. Check and replacement of brushes of screen wipers
   2.18. Shift of tyres
   2.19. Suspension bracket and steering check
   2.20. Exhaust system check
   2.21. Check of level of oil in a transmission and the main transfer
   2.22. Check of level of oil in differential (the main transfer)
   2.23. Check of brake system
   2.24. Check of the vacuum amplifier of brakes
   2.25. Check of a manual brake
   2.26. Check of fuel system
   2.27. Replacement of the fuel filter
   2.28. Check and replacement приводного a belt
   2.29. Check of a free wheeling of a pedal of a brake
   2.30. Check of a free wheeling of a pedal of coupling
   2.31. Check and replacement of spark plugs
   2.32. Check of high-voltage wires
   2.33. Check and adjustment of turns of idling
   2.34. Replacement of the air filter
   2.35. Check and replacement of the valve of ventilation картера (PCV)
   2.36. Check of system of catching of steams of fuel
   2.37. Check of system of repeated burning of the fulfilled gases (EGR)
   2.38. Service of system of cooling
   2.39. Replacement of a brake liquid
   2.40. Oil replacement in an automatic transmission
   2.41. Oil replacement in a mechanical transmission
   2.42. Check and adjustment of backlashes of valves
   + 2.43. The basic malfunctions
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





2.17. Check and replacement of brushes of screen wipers
THE GENERAL DATA

Brushes and rubber elements are necessary for checking periodically on presence of deterioration, cracks and damages.

Check

PERFORMANCE ORDER
1. The film from pitch and a dirt formed on brushes, reduces efficiency of their work, therefore brushes are necessary for washing out from time to time pure water with soap.
2. In the mechanism of a drive of brushes of screen wipers can ослабнуть fastening bolts, therefore at check of brushes of screen wipers it is necessary to check and tighten also all fastenings (on a photo – a tightening of a nut of fastening of the lever of a screen wiper).
3. If rubber elements are worn out, have cracked or deformed or badly clear glass, it is necessary to replace them with the new.

Replacement

PERFORMANCE ORDER
1. Raise the lever of a brush of a screen wiper from a windscreen.
2. From two parties compress steel amplifiers of a rubber tape (it is specified by an arrow) a screen wiper and take a rubber tape of a screen wiper from a brush end face.
3. Establish a new rubber tape in a brush so that brush captures were established for the steel amplifier of a rubber tape, and move a rubber tape into a screen wiper brush.