Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
- 2. Maintenance service
   2.1. Introduction
   2.2. Technical characteristics
   2.3. Periodicity of service
   2.4. Check of level of engine oil
   2.5. Level of a cooling liquid
   2.6. Level of a brake liquid and a liquid of a drive of coupling
   2.7. A liquid for a windscreen washer
   2.8. Accumulator check
   2.9. Tyres and pressure check in tyres
   2.10. Check of level of oil in an automatic transmission
   2.11. Check of level of a liquid in the steering amplifier
   2.12. Replacement of oil and the oil filter
   2.13. Check and accumulator service
   2.14. Accumulator gymnastics
   2.15. Check of system of cooling
   2.16. Check of hoses, tubes and their replacement
   2.17. Check and replacement of brushes of screen wipers
   2.18. Shift of tyres
   2.19. Suspension bracket and steering check
   2.20. Exhaust system check
   2.21. Check of level of oil in a transmission and the main transfer
   2.22. Check of level of oil in differential (the main transfer)
   2.23. Check of brake system
   2.24. Check of the vacuum amplifier of brakes
   2.25. Check of a manual brake
   2.26. Check of fuel system
   2.27. Replacement of the fuel filter
   2.28. Check and replacement приводного a belt
   2.29. Check of a free wheeling of a pedal of a brake
   2.30. Check of a free wheeling of a pedal of coupling
   2.31. Check and replacement of spark plugs
   2.32. Check of high-voltage wires
   2.33. Check and adjustment of turns of idling
   2.34. Replacement of the air filter
   2.35. Check and replacement of the valve of ventilation картера (PCV)
   2.36. Check of system of catching of steams of fuel
   2.37. Check of system of repeated burning of the fulfilled gases (EGR)
   2.38. Service of system of cooling
   2.39. Replacement of a brake liquid
   2.40. Oil replacement in an automatic transmission
   2.41. Oil replacement in a mechanical transmission
   2.42. Check and adjustment of backlashes of valves
   + 2.43. The basic malfunctions
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





2.38. Service of system of cooling
THE GENERAL DATA

Arrangement of stoppers plum of a cooling liquid from the block of cylinders of the engine


The prevention

Replacement of a cooling liquid is made on the cold engine. Avoid hit of a cooling liquid on the painted surfaces of a body and clothes. Otherwise wash out a place where the cooling liquid, a plentiful quantity of water has got.


Plums of a cooling liquid

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports.
2. Establish the big container under a stopper plum of a cooling liquid from a radiator (it is specified by an arrow). Unscrew a stopper and merge cooling liquid.
3. When the stream of the cooling liquid leaving a radiator will stop, establish the container under a drain stopper of the block of cylinders. Unscrew a drain stopper and give the chance to flow down a cooling liquid from the block of cylinders (fig. the Arrangement of stoppers plum of a cooling liquid from the block of cylinders of the engine see).

Washing of system of cooling

Cooling liquid is necessary for changing periodically, and cooling system to wash out, as in system channels the rust and a dirt is formed.

PERFORMANCE ORDER
1. For radiator washing merge cooling liquid from cooling system, then disconnect hoses from the basis and the top tank of a radiator.
2. Insert a garden hose into the top branch pipe of a radiator and pass water through a radiator while water will not leave pure a branch pipe in the radiator basis.
3. If it is not possible to wash out a radiator pure water take advantage of a washing-up liquid.
4. Wash out a heater radiator, preliminary having opened the crane of a heater and having disconnected from a heater hoses. To one of hoses connect a hose and wash out a stream at its finest until water will not follow from the second hose of the pure.

Filling of system of cooling

PERFORMANCE ORDER
1. Before filling of system of cooling make sure that all hoses and collars in a good condition. Pay attention that the antifreeze mix should be used all year long for corrosion prevention. Also check up, that a stopper on a radiator and drain stoppers of the block of cylinders have been established into place.
2. Establish the handle of adjustment of temperature of a heater in position of the maximum temperature.
3. Slowly fill in cooling liquid in a radiator.
4. Without closing a radiator stopper, start the engine and warm up it to working temperature at which the thermostat and a cooling liquid will open will start to proceed through a radiator, thus the top hose of a radiator becomes hot.
5. Switch off and cool the engine, check up level of a cooling liquid and, if necessary, finish it to norm.
6. Compressing the top hose of a radiator, remove air from system of cooling of the engine then add a cooling liquid to demanded level. Establish a radiator stopper into place.
7. Start the engine and warm up it to normal working temperature and check up tightness of system of cooling of the engine.