Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   5.1. Introduction
   5.2. Technical characteristics
   5.3. Pressure removal in fuel system
   5.4. Check of the fuel pump
   5.5. The fuel pump
   5.6. A fuel separator (only models 4WD)
   5.7. The gauge of level of fuel
   5.8. A fuel tank
   5.9. A casing of the air filter
   5.10. An accelerator cable
   5.11. Electronic system of injection of fuel
   5.12. Fuel system
   5.13. System of giving of air
   5.14. Electronic control system
   5.15. Check of system of injection of fuel
   + 5.16. Check and replacement of elements of system of injection of fuel
   5.17. Турбонагнетатель
   5.18. Check of the executive mechanism заслонки турбонагнетателя
   5.19. The general check турбонагнетателя
   5.20. Removal and installation турбонагнетателя
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





5.8. A fuel tank
THE GENERAL DATA

Fuel tank and fuel separator on models 4WD

1 – the canister
2 – a hose
3 – a hose
4 – a hose
5 – a hose
6 – a submitting hose
7 – the fuel filter
8 – a submitting hose
9 – топливопровод
10 – returnable топливопровод
11 – submitting топливопровд
12 – an air hose
13 – an air tube
14 – a protective arm
15 – a cover топливозаливной mouths
16 – sealing rings
17 – a lining
18 – топливозаливная a pipe
19 – an arm
20 – a separator
21 – an arm
22 – a hose In
23 – a hose With
24 – a hose And
25 – an arm
26 – a separator
27 – an arm
28 – a casing
29 – a hose With
30 – a hose And
31 – a hose In
32 – the auxiliary regulating valve of clearing

Fuel tank of models 4WD (on models 2WD the fuel tank is similar)

1 – the block of the fuel pump
2 – the gauge of level of fuel
3 – the fuel pump
4 – the fuel filter
5 – a lining
6 – a hose
7 – an air hose
8 – the tank
9 – fixing tapes
10 – protection
11 – an arm
12 – a casing
13 – the return valve,
14 – a hose,
15 – a submitting hose
16 – a returnable hose
17 – a returnable pipe
18 – a submitting pipe
19 – a pipe
20 – a pipe
21 – an additional submitting hose
22 – a returnable hose
23 – a submitting hose
24 – an additional submitting hose
25 – a hose
26 – a ventilation hose
27 – a ventilation hose
28 – a pipe
29 – an air pipe
30 – an air pipe
31 – a lining
32 – the filter

Fastening топливоналивной pipes and ventilation pipes to a fuel tank

1 – топливнозаливныя a pipe

2 – a ventilation pipe

At removal of a fuel tank fuel level in it should be minimum.

Removal

PERFORMANCE ORDER
1. Uncover топливозаливной mouths to level pressure in a tank with the atmospheric.
2. Remove a wire of weight from the accumulator.
3. Lift the car and fix on supports.
4. Remove a back exhaust pipe and the muffler.
5. On models 4WD remove back differential.
6. On models 4WD remove a back beam.
7. Disconnect топливозаливную a pipe from a fuel tank (fig. Fastening топливоналивной pipes and ventilation pipes to a fuel tank see).
8. Support a fuel tank a jack, having laid between a jack and a fuel tank a board.
9. Remove protection of a fuel tank, then unscrew screws, крепящие two tapes of fastening of a fuel tank.
10. Lower a jack and take a fuel tank from under the car.
11. Installation is made in sequence, return to removal.