Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
- 8. Transmissions
   - 8.1. A mechanical transmission
      8.1.1. Introduction
      8.1.2. Technical characteristics
      8.1.3. The gear change lever
      8.1.4. Check and replacement of support of a transmission
      8.1.5. Switches of light of a backing and neutral position КП
      8.1.6. Removal and transmission installation
   + 8.2. An automatic transmission
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment





8.1.6. Removal and transmission installation

Removal

PERFORMANCE ORDER
1. Open a cowl and fix it in open position.
2. Remove a wire of weight from the accumulator.
3. If on the car it is established тросовый a coupling drive, disconnect a coupling cable. If on the car the hydraulic drive of coupling is established, separate the working cylinder of coupling from a transmission.

The prevention

Do not press a pedal of coupling after removal of the working cylinder of coupling from a transmission.


4. Remove a forward support (fig. of the Detail of the lever of a gear change of models 4WD see). Instead of a forward support it is recommended to establish the special tool for adjustment of an angle of slope of the engine for simplification of removal of a transmission. In the absence of the special tool it is necessary to use a jack slightly to raise a forward part of the engine
5. Mark and disconnect electric sockets from a transmission.
6. Remove a starter.
7. Unscrew the top right bolt of fastening of a transmission to the engine.
8. Lift the car and fix on supports. Merge oil from a transmission.
9. Remove the elements of an exhaust system interfering removal of a transmission.
10. Unscrew the tyre of grounding of a transmission.
11. Disconnect a cable of a drive of a speedometer on the right side of a transmission.
12. On models 4WD remove карданный a shaft.
13. Disconnect from a transmission draught of the shock-absorber, a spring and draught of a gear change.
14. Disconnect hinges of power shafts from a transmission.
15. Prop up a transmission a jack.
16. Unscrew and remove forward, central and back beams.
17. Unscrew two bottom nuts of fastening of a transmission to the engine.
18. Using the special tool established instead of a forward support or using a jack, raise a forward part of the engine so that the back part of the engine was at an angle downwards. Move a transmission from the engine to take an entrance shaft of a transmission from a nave of a disk of coupling, and slowly lower a transmission.

Installation

PERFORMANCE ORDER
1. Apply a thin film universal greasing on grooves of an entrance shaft of a transmission. Raise a transmission and combine it with the engine.
2. Slowly moving a transmission to the engine, insert an entrance shaft of a transmission into a nave of a disk of coupling. Screw the bottom nuts of fastening of a transmission on the engine.
3. Establish back, central and forward beams and fix bolts and nuts.
4. Remove a jack supporting a transmission.
5. Attach to a transmission power shafts.
6. Establish on a transmission draught of the shock-absorber and draught of a gear change.
7. On models 4WD establish карданный a shaft.
8. Establish the elements of an exhaust system removed earlier.
9. Connect electric sockets of the gauge of oxygen, the switch of light of a backing and the switch of neutral position of a transmission.
10. Connect a cable of a drive of a speedometer.
11. Lower the car.
12. Establish the top bolt of fastening to the engine and tighten its demanded moment.
13. Establish a starter.
14. Remove the special tool and establish a forward support.
15. Connect to a transmission the grounding tyre.
16. Establish a cable of coupling and adjust a free wheeling of a cable or establish the working cylinder of coupling on a transmission.
17. Connect to the accumulator a weight wire.
18. Fill in oil in a transmission.